Eiechip CNC 3D Printer Kit for Arduino Mega 2560 R3 + RAMPS 1.4 Controller + LCD 2004 + 6X Limit Switch Endstop + 5 A4988 Stepper Driver

CNC Shield Board:
1>PWM Spindle and direction pins
2>4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
3>2 x End stops for each axis (6 in total)
4>Coolant enable
5>Uses removable A4988 or DRV8825 compatible stepper drivers
6>Compact design
7>Stepper Motors can be connected with 4 pin molex connectors or soldered in place
8>Please note that this is an unassembled kit and Basic soldering skills are needed
A4988 Stepper Motor Driver:
1>Low RDS (On) Output
2>Automatic current decay mode detection / selection
3>Mix with slow current decay modes
4>Synchronous rectification for low power dissipation
5>Internal UVLO
6>Crossover-current protection
7>3.3 and 5 V compatible logic supply
8>Thermal shutdown circuitry
9>Ground fault protection
10>Load short-circuit protection
11>Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
UNO R3 Board for Arduino:
1>MCU: ATmega328
2>USB interface: ATmega16U2
3>Operating voltage: 5V
4>Digital I/O pins: 14 (including 6 with PWM capability)
5>Analog input pins: 6
6>I-I/O pin output current: 40mA max
7>3.3V output current: 150mA max
8>Flash memory: 32kB (0.5kB used by bootloader- included)
9>Static RAM (SRAM): 2kB
10>EEPROM: 1kB
11>Clock speed: 16MHz
LCD 2004 Smart Controller
Easy connect it to your Ramps board using the "smart adapter" included.
After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card.
Further more actions like calibration, axes movements can be done by adjusting the rotary encoder on the Smart Control panel.

View More In 3D Printer Interface & Driver Modules.

Or Browse Our Catalog.

►Nozzle Material: High quality Copper►Heatbreak Material: Stainless steel►Heater Block Material: Aluminum alloy►Nozzle size: 0.4mm►Heatbreak size: M7, Bore 4.2mm►Nozzle Ensure Concentricity and Roundness. ►Support: E3D V6 J-Head Hotend ...

Specification: The board provides flyback diodes (freewheeling diodes) for the motor outputs, so that they are also protected against induction voltages in the unpowered state of the driver. You will get smoother movement especially on the delta-styl...

Specification: The board provides flyback diodes (freewheeling diodes) for the motor outputs, so that they are also protected against induction voltages in the unpowered state of the driver. You will get smoother movement especially on the delta-styl...

The Printing Build Surface Sheet design for FDM 3D printer CR-10 CR-10S Lulzbot TAZ 6 and other more Feature Sticker Size: 305mm x 305mm (12 x 12 inch) Thickness: 0.8mm Weight:0.08kg(0.18lb) Short-term Temperature Support: 120°C ~149°C/ 248°F~300....

Details: Dimensions: 60*50mm Net Weight: 40g Color:Black Max Current: 25A(Enhance heat dissipation) Wire's color is random Summary: 1. Remove basically all ouside screws for your anet a8 control box 2. Take pictures of existing board wiring 3. Uns...

►Nozzle Material: High quality Copper►Heatbreak Material: Stainless steel►Heater Block Material: Aluminum alloy►Nozzle size: 0.4mm►Heatbreak size: M6, Length: 30mm, With PTFE Teflon►Nozzle Ensure Concentricity and Roundness. ►Support: M...

TL-Smoother kit addon module for pattern elimination motor filter clipping filter 3D printer motor drivers ControllerProduct DescriptionThe TL-Smoother is an addon module for 3D printer stepper motor drivers.The board provides flyback diodes (freewhe...

►Nozzle Material: High quality Copper►Heatbreak Material: Stainless steel►Heater Block Material: Aluminum alloy►Nozzle size: 0.4mm►Heatbreak size: M6, Length: 26.5mm, With PTFE Teflon►Nozzle Ensure Concentricity and Roundness. ►Support:...

The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.4 board using "smart adapter" included. This panel connect your RAMPS 1.4, you do not need your...