SainSmart TB6600 CNC Micro-Stepping Stepper Motor Driver 4.5A

Overview:

This drive adopts Toshiba TB6600HG driver chip, which runs smoothly, the motor is locked without noise, and
the protection functions such as overcurrent, overheating, reverse connection, freewheeling, etc.
Maximum output phase current 4.5A, input voltage 12-40VDC. It is a low-cost, cost-effective driver.

Drive Identification Introduction:

DC+: positive power supply
The supply voltage should not be higher than 40V. It is recommended to use 24V or 36V switching power supply.
The power supply depends on the size of the motor.
DC-: negative electrode
A+, A-: Motor Phase
B+, B-: Motor Phase
PUL+, PUL -: pulse signal
DIR +, DIR-: direction signal
ENA+, ENA-: Enable signal

Packing list:

1. ST-4045-A1 X1
2. Paper Manual Instruction X1

View More In 3D Printer Motors.

Or Browse Our Catalog.

5PCS 17HS3401 4-lead Nema 17 Stepper Motor 42 motor 42BYGH 1.3A CE CNC Laser Grind Foam Plasma Cut It is D axis ....

power requirements, current is less than 12 v Package Included: 3*Heat bed Power Module Note: Please double-confirm the wire you connect is right, if there have any issue please contact us before leave negative review and feedback, thanks!Currently w...

This is the highest torque for Nema 8 stepper motor with 1.8 deg. step angle (200 steps/revolution). Each phase draws 600mA, allowing for a holding torque of 4Ncm(5.7oz.in). Electrical Specification: * Manufacturer Part Number: 8HS15-0604S * Motor Ty...

Stepper Motor : Motor type: Bipolar Stepper Motor Length: 40mm Phase Resistance: 1.5Ohm Phase Inductance: 2.8mH Detent Torque: 2.2N.cm Rotor Inertia: 54g.cm2 Holding Torque: 40N.cm Motor Weight: 280g Step angle: 1.8 deg Step angle accuracy: + - 5%(fu...

Specification: Motor type: bipolar stepper Step Angle: 1.8 deg. Holding Torque: 13Ncm(18.4oz.in) Rated Current/phase: 1A Phase Resistance: 3.5ohms Inductance: 4.5mH+/-20%(1KHz) Weight: 120g Frame Size: 42 x 42mm Body Length: 20mm Shaft Diameter: 5mm...

This is strongest model for hybrid bipolar Nema 14 stepper motor, step angle is 1.8 deg. (200 steps/revolution). Each phase draws 1.5 A at 4.2 V, allowing for a holding torque of 40Ncm(56.7oz-in). Electrical Specification: * Manufacturer Part Num...

5 new NEMA17 bipolar stepper motor. Ideal for 3D Printers and other applications. The Motors are 2A, 1.8deg, single shaft (20mm long, 5mm diameter) model with holding torque 84 oz-in/0.59 N.m. 4-wire connection (Black, Green, Blue, Red) with plug on ...

Left versions of this extruder kit.All necessary hardware is included in the kit as the picture shows. To complete setup you will need PTFE tubing with 4mm OD and 2mm ID and connected extrusion head (hotend). Package List: 1 x Aluminum main extruder...

This hybrid bipolar stepper motor is the miniature stepper motor we carry, it with 1.8 deg. step angle (200 steps/revolution). Each phase draws 200 mA at 4.8 V, allowing for a holding torque of 1.6Ncm(2.3oz.in). Electrical Specification: * Manufactur...

Descriptions: These vibration dampers  are used for reducing stepper motor noise and vibration. Suitable for NEMA 17 Motor/3D Printer Motor. Specifications: Material:metal, rubber Quantity: 5 Hole diameter: 2.1cm/0.8inch Weight: 96g Pack...